Parámetros técnicos del inserto roscado del alambre de la bobina de funcionamiento libre modificado - Conocimiento de la industria

W y d1 son los valores de control para las inserciones de hilos (ejecución libre) antes de que se hayan instalado.

La longitud solo se puede medir para las inserciones de rosca instaladas.

imagen

d = diámetro nominal del hilo

P = paso de rosca

d1 = diámetro exterior del inserto de rosca antes de la instalación

W = Número de hilos antes de la instalación

DHC = Diámetro exterior del hilo principal

D1HC = Diámetro de la cresta

B = Diámetro adecuado del taladro de torsión. Tenga en cuenta:

D1HC es fundamental para seleccionar el diámetro correcto de la broca helicoidal

t1 = profundidad mínima del orificio roscado

t2 = La longitud nominal de la inserción del hilo corresponde a la longitud mínima del hilo principal completo para ciegos

Orificios o el espesor mínimo de la placa para un orificio pasante.

t3 = Máxima profundidad de atornillado cuando no se elimina la espiga

t5 = Distancia del inserto del hilo desde la cara de la junta = 0.25 a 0.5 P, si t2 corresponde a lo mencionado anteriormente

valor mínimo

Parámetros técnicos - Métrica

dx p	xd	L (mm)	W	d1 min.max (mm)	B (mm)
M1.6x0.35	1d	1.6	3.1	2.1 ～ 2.3	1.6
	1.5d	2.4	4.5
	2d	3.2	6.2
M2x0.4	1d	2	3.2	2.5 ～ 2.8	2.1
	1.5d	3	5.3
	2d	4	7.4
	2.5d	5	9.5
	3d	6	11.6
M2.5x0.45	1d	2	3.6	3.3 ～ 3.5	2.6
	1.5d	3.8	5,9
	2d	5	8.2
	2.5d	6.3	10.5
	3d	7.5	12.8
M3x0.5	1d	3	4.2	3.8 ～ 4	3.1
	1.5d	4.5	6.8
	2d	6	9.4
	2.5d	7.5	12
	3d	9	14.6
M3.5x0.6	1d	3.5	4	4.55 ～ 4.75	3.7
	1.5d	5.3	6.4
	2d	7	8.9
	2.5d	8.8	11.4
	3d	10.5	13.9
M4x0.7	1d	4	4	5.05 ～ 5.25	4.2
	1.5d	6	6.6
	2d	8	9.1
	2.5d	10	11.7
	3d	12	14.2
M5x0.8	1d	5	4.4	6.35 ～ 6.6	5.2
	1.5d	7.5	7.1
	2d	10	9.9
	2.5d	12.5	12.6
	3d	15	15.3
M6x1	1d	6	4.3	7.6 ～ 7.85	6.3
	1.5d	9	6.9
	2d	12	9.6
	2.5d	15	12.2
	3d	18	14.9
M7x1	1d	7	5.2	8.65 ～ 8.9	7.3
	1.5d	10.5	8.3
	2d	14	11.5
	2.5d	17.5	14.6
M8x1.25	1d	8	4.8	9.85 ～ 10.1	8.3
	1.5d	12	7.7
	2d	dieciséis	10.6
	2.5d	20	13.5
	3d	24	16.5
M8x1	1d	8	6	9.85 ～ 10.1	8.3
	1.5d	12	9.6
	2d	dieciséis	13.1
	2.5d	20	16.7
M10x1.5	1d	10	5	12.1 ～ 12.5	10.4
	1.5d	15	8.1
	2d	20	11.2
	2.5d	25	14.2
	3d	30	17.3
M10x1.25	1d	10	6.1	12.1 ～ 12.5	10.3
	1.5d	15	9.7
	2d	20	13.3
	2.5d	25	16.9
M10x1	1d	10	7.7	12.0 ～ 12.5	10.3
	1.5d	15	12.1
	2d	20	16.5
	2.5d	25	20.8
M11x1.5	1d	11	5.7	13.0 ~ 13.4	11.4
	1.5d	16.5	9.1
	2d	22	12.5
M12x1.75	1d	12	5.3	14.3 ~ 14.8	12.4
	1.5d	18	8.4
	2d	24	11.6
	2.5d	30	14.8
	3d	36	18
M12x1.5	1d	12	6.2	14.3 ~ 14.8	12.4
	1.5d	18	9.8
	2d	24	13.5
	2.5d	30	17.1
M12x1.25	1d	12	7.5	14.3 ～ 14.8	12.3
	1.5d	18	11.8
	2d	24	16.1
	2.5d	30	20.3
M12x1	1d	12	9.4	14.3 ～ 14.8	12.3
	1.5d	18	14.7
	2d	24	19.9
M14x2	1d	14	5.4	16.7 ～ 17.2	14.5
	1.5d	21	8,7
	2d	28	11.9
	2.5d	35	15.2
	3d	42	18.4
M14x1.5	0.75d	10.5	5.2	16.7 ～ 17.2	14.4
	1d	14	7.3
	1.5d	21	11.5
	2d	28	15.7
	2.5d	35	19.9
M14x1.25	1d	14	8.8	16.7 ～ 17.2	14.3
M14x1.25	1.5d	21	13.8	16.7 ～ 17.2	14.3
M 16x2	1d	dieciséis	6.3	18.8 ～ 19.4	16.5
	1.5d	24	10
	2d	32	13.7
	2.5d	40	17.5
	3d	48	21.2
M16x1.5	0.75d	12	6.1	18.8 ～ 19.4	16.4
	1d	dieciséis	8.5
	1.5d	24	13.3
	2d	32	18.1
M18x2.5	1d	18	5.6	21.4 ~ 22	18.6
	1.5d	27	9
	2d	36	12.3
	2.5d	45	15.7
	3d	54	19
M18x2	0.75d	13.5	5	21.4 ~ 22	18.5
	1d	18	7.1
	1.5d	27	11.2
	2d	36	15.2
M18x1.5	0.75d	13.5	7.1	21.4 ~ 22	18.4
	1d	18	9.8
	1.5d	27	15
	2d	36	20.3
M20x2.5	1d	20	6.5	23.6 ~ 24.2	20.6
	1.5d	30	10
	2d	40	13.8
	2.5d	50	17.5
	3d	60	21.2
M20x2	0.75d	15	5.7	23.6 ~ 24.2	20.5
	1d	20	8
	1.5d	30	12.5
	2d	40	17.1
M20x1.5	0.5d	10	4.8	23.6 ~ 24.2	20.4
	0.75d	15	7.8
	1d	20	10.7
	1.5d	30	16.7
M22x2.5	1d	22	6.9	26.2 ～ 26.8	22.6
	1.5d	33	11
	2d	44	15
	2.5d	55	19
	3d	66	23
M 22x2	0.75d	16.5	6.3	26.2 ～ 26.8	22.5
	1d	22	8.8
	1.5d	33	13.7
	2d	44	18.6
M22x1.5	0.5d	11	5.4	26.2 ～ 26.8	22.4
	0.75d	16.5	8,7
	1d	22	11.9
	1.5d	33	18.4
M 24x3	1d	24	6.3	28.5 ~ 29.1	24.8
	1.5d	36	10
	2d	48	13.7
	2.5d	60	17.5
	3d	72	21.2
M24x2	0.75d	18	7	28.5 ~ 29.1	24.5
	1d	24	9.6
	1.5d	36	15
	2d	48	20.3
M 24x1.5	0.5d	12	6	28.4 ~ 28.9	24.4
	0.75d	18	9.5
	1d	24	13
	1.5d	36	20
M26x1.5	0.5d	13	6.5	28.5 ~ 30	26.4
	0.75d	19.5	10.3
	1d	26	14
M27x3	1d	27	7.2	32.1 ~ 32.5	27.8
	1.5d	40.5	11.3
	2d	54	15.4
	2.5d	67.5	19.5
M27x2	0.75d	20.3	7.9	32.1 ~ 32.2	27.5
	1d	27	10.9
	1.5d	40.5	16.9
M27x1.5	0.5d	13.5	6.9	31.3 ~ 32.1	27.4
	0.75d	20.3	10.9
	1d	27	14.9
	1.5d	40.5	22.8
M28x1.5	0.5d	14	7.1	33.0 ～ 33.6	28.4
	0.75d	21	11.2
	1d	28	15.3
	1.5d	42	23.5
M30x3.5	1d	30	6.9	35.0 ～ 35.6	30.9
	1.5d	45	11
	2d	60	15
	2.5d	75	19
M30x2	0.5d	15	5.6	34.7 ～ 35.3	30.5
	0.75d	22.5	9
	1d	30	12.3
	1.5d	45	19
M30x1.5	0.5d	15	7.8	34.3 ~ 34.9	30.4
	0.75d	22.5	12.2
	1d	30	16.7
	1.5d	45	25.5
M33x3.5	1d	33	7.8	38.1 ~ 38.6	33.9
	1.5d	49.5	12.2
	2d	66	16.6
	2.5d	82.5	21.1
	3d	99	25.5
M33x2	0.5d	16.5	6.4	38.0 ~ 38.5	33.5
	0.75d	24.8	10.1
	1d	33	13.8
	1.5d	49.5	21.2
M33x1.5	0.5d	16.5	8,7	37.8 ~ 38.3	33.4
	0.75d	24.8	13.6
	1d	33	18.5
M36x4	0.75d	27	5.2	41.9 ~ 42.3	37
	1d	36	3.7
	1.5d	54	11.6
	2d	72	15.8
M36x3	0.5d	18	4.4	41.8 ~ 42.3	36.8
	0.75d	27	7.1
	1d	36	9.9
	1.5d	54	15.4
M36x2	0.5d	18	6.9	41.7 ~ 42.3	36.5
	0.75d	27	11
	1d	36	15
	1.5d	54	23
M39x2	0.5d	19.5	7.7	44.8 ～ 45.4	39.5
	0.75d	29.3	12.1
	1d	39	16.4
M42x4.5	1d	42	7.3	49 ～ 51	43
	1.25d	52	9.5
	1.5d	63	11.6
M42x3.0	1d	42	11.7	48 ～ 50.5	43
	1.25d	52	14.8
	1.5d	63	18.1
M48x3	0.5d	24	6.2	55 ~ 55.5	48.8
	0.75d	36	9.9
	1d	48	13.6
M56x4	0.5d	28	5.4	64 ~ 65	17
	0.75d	42	8.6
	1d	56	11.8
M60x3	0.5d	30	7.9	69 ~ 70	60.8
	0.75d	45	12.4
	1d	60	16.9
	1.5d	90	25.9
M60x4	0.5d	30	5.8	69 ~ 70	61
	0.75d	45	9.2
	1d	60	12.6
	1.5d	90	19.5

Parámetros Técnicos - UNC / UNF

d número-hilos	re	pag	xd	L (mm)	W	d1 min.max (mm)	B (mm)
2-56	2.184	0.45	1d	2.18	3.3	2.7-3.1	2.3
			1.5d	3.28	5
			2d	4.37	6.8
4-40	2.845	0.64	1d	2,90	3.2	3.6-4.0	3.0
			1.5d	4.30	5.1
			2d	5.80	7.2
5-40	3.175	0.64	1d	3.20	3.7	4.0-4.4	3.3
			1.5d	4.80	5,9
			2d	6.40	8.2
6-32	3.505	0.79	1d	3,50	2.8	4.5-4.9	3.7
			1.5d	5.30	4.8
			2d	7.00	6.8
8-32	4.166	0.79	1d	4.20	4	5.2-5.6	4.4
			1.5d	6.25	6
			2d	8.30	8,7
8-36	4.166	0.71	1d	4.20	4.5	5.1-5.6	4.3
			1.5d	6.30	7.2
			2d	8.30	9.7
10-24	4.826	1.06	1d	4.80	3.3	6.1-6.6	5.1
			1.5d	7.20	5.4
			2d	9.60	7.5
10-32	4.826	0.79	1d	4.83	4.3	5.9-6.5	5.0
			1.5d	7.24	6.9
			2d	9.60	9.5
12-24	5.486	1.06	1d	5,50	4	6.8-7.2	5.8
			1.5d	8.20	6.3
			2d	11.00	8.8
1/4 '' - 20	6.35	1.27	1d	6.40	3.9	7.8-8.3	6.7
			1.5d	9.50	6.2
			2d	12.70	8.6
1/4 '' - 28	6.35	0.91	1d	6.35	5.3	7.7-8.3	6.6
			1.5d	9.50	8.6
			2d	12.70	11.8
5/16 '' - 18	7.938	1.41	1d	7.90	4.3	9.6-10.2	8.3
			1.5d	11.90	6.8
			2d	15.90	9.4
5/16 '' - 24	7.938	1.06	1d	7.90	5,9	9.6-10.2	8.2
			1.5d	11.90	9.4
			2d	15.90	12.8
3/18 '' - 16	9.525	1.59	1d	9.50	4.8	11.4-11.9	9.9
			1.5d	14.30	7.7
			2d	19.10	10.6
3/8 '' - 24	9.525	1.06	1d	9.50	7.3	11.4-11.9	9.8
			1.5d	14.30	11.5
			2d	19.10	15.6
7/16 '' - 14	11.113	1.81	1d	11.10	4.9	13.3-13.9	11.6
			1.5d	16.70	7.9
			2d	22.20	10.7
7/16 '' - 20	11.113	1.27	1d	11.10	7	13.3-13.7	11.4
			1.5d	16.70	11.1
			2d	22.20	15
1/12 '' - 13	12.7	1.95	1d	12.70	5.2	15.1-15.7	13.2
			1.5d	19.10	8.3
			2d	25.40	11.4
1/12 '' - 20	12.7	1.27	1d	12.70	7.9	15-15.6	13.0
			1.5d	19.10	12.8
			2d	25.40	17.3
9/16 '' - 18	14.288	1.41	1d	14.30	7.9	16.91-17.55	14.6
			1.5d	21.50	12
			2d	28.60	dieciséis
5/8 '' - 11	15.875	2,31	1d	15.9	5.7	18.8-19.4	16.5
			1.5d	23.8	9
			2d	31.8	12.3
5/8 '' - 18	15.875	1.41	1d	15.9	9.4	18.6-19.3	16.2
			1.5d	23.8	14.5
			2d	31.8	19.7
3/4 '' - 10	19.05	2.54	1d	19.1	6.3	22.3-23.0	19.7
			1.5d	28.6	9.9
			2d	38.1	13.5
3/4 '' - 16	19.05	1.59	1d	19.1	10.1	22.2-22.8	19.4
			1.5d	28.6	15.6
			2d	38.1	21
7/8 '' - 14	22.225	1.81	1d	22.2	10.3	25.9-26.7	22.6
			1.5d	33.3	15.9
			2d	44.5	21.6
1/8 '' - 14	25.4	3.18	1d	25.4	6.8	29.6-30.4	26.1
			1.5d	38.1	10.6
			2d	50.8	15.4
1 '' - 12	25.4	2.12	1d	25.4	10	29.6-30.4	30.0
			1.5d	38.1	15.6
			2d	25.4	11.8
1 '' - 14	25.4	1.81	1d	25.4	11.8	29.6-30.4	25.9
			1.5d	38.1	18.1
			2d	50.8	24.5

Parámetros técnicos del inserto roscado de alambre de bobina de funcionamiento libre modificado